How a 0–1 Bar Pressure Transmitter Works: Internal Components and Installation Materials

The following describes common construction options and installation accessories. The exact components and required accessories depend on the selected model and application.

Internal Components (Inside the Transmitter)

Manufacturers combine a sensing assembly and signal-conditioning electronics; the construction varies between product families.

• Sensing Element: Common options include piezoresistive silicon, ceramic thick-film, metal thin-film and capacitive designs. Pressure changes resistance or capacitance depending on technology. Range alone does not establish diaphragm thickness, accuracy or overload capability.
• Process Diaphragm: The pressure-sensitive or isolating surface may be metallic or ceramic. Examples include stainless steel, alumina ceramic and specialist alloys. Verify all wetted materials, including seals, for the process fluid and temperature.
• Internal Fill Fluid (where used): In some isolated sensing assemblies, a liquid transmits pressure from the process diaphragm to the sensing element. Other designs are oil-free. Fill fluid is not a general substitute for pulsation protection. Oxygen service requires manufacturer-approved materials, cleanliness and construction; oil type alone is insufficient.
• ASIC/Circuit Board: Internal electronics that amplify, linearize, and convert the tiny sensor fluctuations into a standard industrial signal (like 4–20 mA or 0–10 V).
• Housing/Enclosure: Material and ingress protection depend on the product and environment. Select suitable protection for dust, washing, condensation or immersion. The stated rating may require the correct mated connector and cable installation.
• Atmospheric Reference: A vented gauge-pressure transmitter references local atmospheric pressure through an arrangement determined by its design. Protect the reference path from blockage and moisture according to the installation instructions. Absolute-pressure versions use a different reference.

External Materials (Needed for Installation & Operation)

Provide the accessories required by the installation; adapters and impulse tubing are unnecessary where a suitable direct connection is available.

1. Mechanical Piping & Process Connection

• Process Fitting: Match the exact transmitter connection, sealing face and pressure/temperature rating. Common options include G1/4, G1/2, 1/4 NPT and 1/2 NPT, but these are not interchangeable.
• Sealing Material: Use an approved sealant for tapered threads where specified. Parallel G connections normally seal at a designated face using the specified washer or O-ring. Select seals for the medium, temperature and connection geometry; follow the manufacturer’s assembly instructions.
• Impulse Piping / Tubing (where required): Select compatible tubing for pressure, temperature and fluid service. Account for leaks, blockage, trapped gas or liquid, and hydrostatic offsets. Direct mounting may eliminate the need for tubing.
• Isolation Valve (where required): Select a compatible valve for the maximum possible pressure and temperature, including abnormal conditions. Provide safe depressurisation before removing or calibrating the transmitter; closing a valve alone may leave trapped pressure.

2. Electrical Materials

• Power Supply: 24 VDC is common, but use the model’s specified voltage range. For a two-wire loop, allow sufficient voltage for the transmitter, receiver, wiring resistance and any barriers or isolators.
• Cabling / Wiring: Use the specified cable and wiring arrangement. A two-wire 4–20 mA transmitter commonly uses a twisted pair; voltage or digital versions may need additional conductors. Correct shielding and routing reduce electromagnetic interference. Select conductor size for loop resistance and installation conditions.
• Mating Connector: Match the specified connector form, pinout, seal and protection rating, such as the applicable EN 175301-803 (formerly DIN 43650) form or M12 version. For hazardous areas, the transmitter and installation must have appropriate approvals; a certified gland does not upgrade an ordinary transmitter.

3. Control & Monitoring System

• Receiver Device: An instrument to read and scale the electrical signal, such as a Digital Panel Meter, a PLC (Programmable Logic Controller), or a DCS (Distributed Control System) input card.
• Loop Resistor (if applicable): A suitable 250 Ω resistor converts 4–20 mA into 1–5 V across it. Use this only with an appropriate voltage input and adequate loop voltage. Do not automatically add a resistor across a current input; account for its existing resistance and follow the receiver wiring instructions.

Installation note: follow the model’s instructions for mounting, wiring, shielding, bonding and commissioning. Confirm zero and span scaling against the receiver and use pressure protection where the application requires it.